Thursday, 14 July 2022 09:10 Written by

CFL SG 0810

Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator and SIM Filter for fault distance measurement and also used with Pin Pointer Set for pinpointing the exact fault spot.

SCOPE offers CFL SG 0810, Surge Generator with output of 8kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to MV. CFL SG series is equipped with different Protections, Interlocks and Auto-discharge facility to ensure user safety during operation. User friendly controls, adequate form factor, contact free HV terminations makes this CFL SG series most durable and best-designed sets in the segment

Features

  • Compact, Lightweight, and housed in rugged aluminum case
  • Ideal choice for fault location on all type of power cables
  • Backbone of Cable Fault Locator System
  • Generates short duration high voltage surge for fault break down
  • Built-in Current Coupler to determine the fault distance in conjunction with Prelocator unit
  • Repetitive surges applied for pinpointing the exact fault location in conjunction Pinpointing set
  • Supports SIM/ARM/MIM method for locating High resistance and flashing faults along with Prelocator and SIM Filter from CFL Series
  • Available with optional modes such as DC Hi-Pot, Burn Down and Sheath Fault Location Mode
  • Multiple options in a single instrument to avoid carrying several heavy instruments to the site
  • Easy setup and intelligent protections make high voltage testing safe & reliable
  • Compatible with other models of SCOPE make CFL Series

Specifications

Parameter CFL SG 0810
Output Voltage Ranges 0 – 2kV / 4kV / 8kV selectable
Output Energy Max. 1000J in each voltage range

Impulse Sequence (Surge Rate)

Single Impulse (Manual) - 3 Sec / 6 Sec / 9 Sec or

Single Impulse (Manual) - 2 Sec / 4 Sec / 8 Sec (Optional)

Output Indication Moving Coil Analog Meter for Output Voltage measurement 
Measurement Accuracy ±5% of selected range
Input Supply

230V AC ± 10%, 50/60Hz ± 10%, Single Phase

Cooling Type Air Cooled
Dimensions

725 x 540 x 780mm 

Weight  (without wheels and test leads)

90kg approx.

Environmental (Operation)

0°C to 50°C, up to 95% RH (Non-Condensing)

Environmental (Storage)

-10°C to 55°C, up to 95% RH (Non-Condensing)

Thursday, 14 July 2022 08:45 Written by

CFL SG 1610

Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator and SIM Filter for fault distance measurement and also used with PinPointer Set for pinpointing the exact fault spot.

SCOPE offers CFL SG 1610, Surge Generator with output of 16kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment

Features

  • Compact, Lightweight, and housed in rugged aluminum case
  • Ideal choice for fault location on all type of power cables
  • Backbone of Cable Fault Locator System
  • Generates short duration high voltage surge for fault break down
  • Built-in Current Coupler to determine the fault distance in conjunction with Prelocator unit
  • Repetitive surges applied for pinpointing the exact fault location in conjunction Pinpointing set
  • Supports SIM/ARM/MIM method for locating High resistance and flashing faults along with Prelocator and SIM Filter from CFL Series
  • Available with optional modes such as DC Hi-Pot, Burn Down and Sheath Fault Location Mode
  • Multiple options in a single instrument to avoid carrying several heavy instruments to the site
  • Easy setup and intelligent protections make high voltage testing safe & reliable
  • Compatible with other models of SCOPE make CFL Series

Specifications

Parameter CFL SG 1610
Output Voltage Ranges 0 – 4kV / 8kV / 16kV selectable
Output Energy Max. 1000J in each voltage range

Impulse Sequence (Surge Rate)

Single Impulse (Manual) - 3 Sec / 6 Sec / 9 Sec or

Single Impulse (Manual) - 2 Sec / 4 Sec / 8 Sec (Optional)

Output Indication Moving Coil Analog Meter for Output Voltage measurement Moving Coil Analog Meter for Leakage Current measurement in Optional DC Modes
Measurement Accuracy ±5% of selected range
Input Supply

230V AC ± 10%, 50/60Hz ± 10%, Single Phase,

1.2 kVA max.

Cooling Type Air Cooled
Dimensions

680 x 480 x 660mm without Optional DC Modes 

835 x 810 x 880 mm with Optional DC Modes

Weight  (without trolley and test leads)

Without Optional DC Modes: 150kg approx.

With Optional DC Modes: 155kg approx.

Environmental (Operation)

0°C to 50°C, up to 95% RH (Non-Condensing)

Environmental (Storage)

-10°C to 55°C, up to 95% RH (Non-Condensing)

Optional DC Modes Voltage Current Timer / Pulse Ratio*
Hi-Pot 0-16kV 3/6/12mA 5/10/15min
Burn Down 0-4/8/16kV 90/60/30mA 3min
Sheath Fault 0-8kV 60mA *3/6/9s On & 100ms Off
Thursday, 14 July 2022 08:26 Written by

CFL SG 3210

Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator and SIM Filter for fault distance measurement and also used with PinPointer Set for pinpointing the exact fault spot.

SCOPE offers CFL SG 3210, Surge Generator with output of 32kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment.

Features

  • Compact, Lightweight, and housed in rugged aluminum case
  • Ideal choice for fault location on all type of power cables
  • Backbone of Cable Fault Locator System
  • Generates short duration high voltage surge for fault break down
  • Built-in Current Coupler to determine the fault distance in conjunction with Prelocator unit
  • Repetitive surges applied for pinpointing the exact fault location in conjunction Pinpointing set
  • Supports SIM/ARM/MIM method for locating High resistance and flashing faults along with Prelocator and SIM Filter from CFL Series
  • Available with optional modes such as DC Hi-Pot, Burn Down and Sheath Fault Location Mode
  • Multiple options in a single instrument to avoid carrying several heavy instruments to the site
  • Easy setup and intelligent protections make high voltage testing safe & reliable
  • Compatible with other models of SCOPE make CFL Series

Specifications

Parameter CFL SG 3210
Output Voltage Ranges 0 – 8kV / 16kV / 32kV selectable
Output Energy Max. 1000J in each voltage range

Impulse Sequence (Surge Rate)

Single Impulse (Manual) / 3 Sec / 6 Sec / 9 Sec or

Single Impulse (Manual) / 2 Sec / 4 Sec / 8 Sec (Optional)

Output Indication Moving Coil Analog Meter for Output Voltage measurement Moving Coil Analog Meter for Leakage Current measurement in Optional DC Modes
Measurement Accuracy ±5% of selected range
Input Supply

230V AC ± 10%, 50/60Hz ± 10%, Single Phase,

1.8 kVA max.

Cooling Type Air Cooled
Dimensions 835 x 810 x 880 mm
Weight  (without trolley and test leads)

Without Optional DC Modes: 150kg approx.

With Optional DC Modes: 155kg approx.

Environmental (Operation)

0°C to 50°C, up to 95% RH (Non-Condensing)

Environmental (Storage)

-10°C to 55°C, up to 95% RH (Non-Condensing)

Optional DC Modes Voltage Current Timer / Pulse Ratio*
Hi-Pot 0-32kV 6/12/24mA 5/10/15min
Burn Down 0-8/16/32kV 240/120/60mA 3min
Sheath Fault 0-8kV 240mA *3/6/9s On & 100ms Off
Thursday, 14 July 2022 07:07 Written by

CFL SG 3220

Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator and SIM Filter for fault distance measurement and also used with PinPointer Set for pinpointing the exact fault spot.

SCOPE offers CFL SG 3220, Surge Generator with output of 32kV and 2000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment.

Features

  • Compact, Lightweight, and housed in rugged aluminum case
  • Ideal choice for fault location on all type of power cables
  • Backbone of Cable Fault Locator System
  • Generates short duration high voltage surge for fault break down
  • Built-in Current Coupler to determine the fault distance in conjunction with Prelocator unit
  • Repetitive surges applied for pinpointing the exact fault location in conjunction Pinpointing set
  • Supports SIM/ARM/MIM method for locating High resistance and flashing faults along with Prelocator and SIM Filter from CFL Series
  • Available with optional modes such as DC Hi-Pot, Burn Down and Sheath Fault Location Mode
  • Multiple options in a single instrument to avoid carrying several heavy instruments to the site
  • Easy setup and intelligent protections make high voltage testing safe & reliable
  • Compatible with other models of SCOPE make CFL Series

Specifications

Parameter CFL SG 3220
Output Voltage Ranges 0 – 8kV / 16kV / 32kV selectable
Output Energy Max. 2000J in each voltage range

Impulse Sequence (Surge Rate)

Single Impulse (Manual) / 3 Sec / 6 Sec / 9 Sec or        Single Impulse (Manual) / 2 Sec / 4 Sec / 8 Sec (Optional)

Output Indication Moving Coil Analog Meter for Output Voltage measurement Moving Coil Analog Meter for Leakage Current measurement in Optional DC Modes
Measurement Accuracy ±5% of selected range
Input Supply 230V AC ± 10%, 50/60Hz ± 10%, Single Phase, 1.8 kVA max.
Cooling Type Air Cooled
Dimensions 835 x 810 x 880 mm
Weight  (without trolley and test leads)

Without Optional DC Modes: 160kg approx.

With Optional DC Modes: 165kg approx.

Environmental (Operation)

0°C to 50°C, up to 95% RH (Non-Condensing)

Environmental (Storage)

-10°C to 55°C, up to 95% RH (Non-Condensing)

Optional DC Modes Voltage Current Timer / Pulse Ratio*
Hi-Pot 0-32kV 6/12/24mA 5/10/15min
Burn Down 0-8/16/32kV 240/120/60mA 3min
Sheath Fault 0-8kV 240mA *3/6/9s On & 100ms Off
Monday, 24 January 2022 07:00 Written by

MD 5KVr

The digital insulation tester model MD5KVR is TENTECH's cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TΩ, with 4 preselected test voltages, 500 V -1 kV - 2,5 kV - 5 kV. Other test voltages, from 50 V to 5 kV, can be selected in 25 V or 500 V steps.

A state-of-the-art microprocessor controls the equipment operation and enables the incorporation of advanced features which make measurements easier: auto-range selection, AC/DC voltmeter, automatic measurement of absorption index, polarization index, leakage current and capacitance, timer enabling programming of test duration, configurable pass-fail test, dielectric discharge, ramp test, step voltage test, built-in printer, real time clock and calendar.

Measured values are transmitted through the USB interface and are printed in the built-in printer as a registration of the performed test. Furthermore, the measured values are stored in a non-volatile internal memory. Up to 16,000 measured values may be stored to be transferred afterward to a computer running the T-Logger program. This software allows a further analysis of the test results, including a graphical representation and automatic report generation. The real time clock and calendar, and the sequential test number, facilitates the identification of each test, and the organization of a predictive maintenance system by trend analysis.

The MD5KVR is powered by a rechargeable LFP battery. The cabinet is strong and lightweight, easy to carry, impact-resistant and suitable to be used under severe weather conditions. Thus the megohmmeter supplies very reliable and accurate measurements both in laboratory and out in the field.

 

Features

 

  • Microprocessor-controlled
  • Insulation resistances up to 5 TΩ
  • Auto-range
  • Automated tests: Absorption index, Polarization index, Capacitance, Leakage current and AC/DC voltmeter
  • IP65 protection 
  • Switchable filter to remove external noise interference
  • Real time clock and calendar
  • Built-in printer, internal memory for up to 16,000 measured values
  • Software for data management

Specifications

Specification  MD 5KVR
Test voltage

500 V - 1 kV - 2,5 kV - 5k V directly, one button selectable.

50 V to 5 kV in 25 V or 500 V steps. DC, negative.

Maximum resistance reading

5 TΩ @ 5 kV 

250GΩ @250V

DC Voltmeter

 15 V up to 1,000 Vdc.

Accuracy: ±(5% of reading + 3 digits).

AC voltmeter

 15 V up to 1000 V r.m.s.

Accuracy: ±(5% of reading + 3 digits)

 Overvoltage Category   CAT -III 600V
 Capacitance measurement

50 nF up to 10 µF @ 500 V.

50 nF up to 5 µF @ 1,000 V.

30 nF up to 2 µF @ 2,500 V.

30 nF up to 1 µF @ 5,000 V.

Accuracy: ±10% of reading ± 3 digits.

 Short circuit current  Max. 3 mA
 Test voltage accuracy  ± 3% of nominal test voltages on 10 GΩ
 Insulation tester basic accuracy

± 5% of reading from 1 MΩ to 1 TΩ @ 5 kV.

± 20% of reading from 1 TΩ to 5 TΩ @ 5 kV.

(for lower test voltages, the upper limit will be reduced proportionally).

± 20% of reading ± 5 digits 10 from kΩ to 100 kΩ.

± 10% of reading ± 5 digits 100 from kΩ to 1 MΩ

Advanced features

Ramp test.

Dielectric discharge.

Step voltage test.

Automated polarization index calculation.

Automated dielectric absorption ratio calculation.

Programmable pass-fail test.

16,000 readings memory.

Switchable filter to remove external noise interference.

Wednesday, 13 January 2021 11:25 Written by

TI 330+

TI330+ is with a cooled detector(T2SL, NETD<25mK) to detect gas leaks and pinpoint the gas leaks location accurately, also offers temperature measurement. It is a multifunctional device for gas leakage detection and thermography applications.

TI330+ provide safe & efficient inspection at long distance without shutting systems down, scans large areas & numerous objects rapidly, sees into areas that are difficult to reach with contact measurement tools and enhances predictive maintenance at the same time. It is an ideal device for chemical/petrochemical application such as offshore platforms, oil refineries and natural gas processing plants

Features

      • Cooled T2SL detector, sensitivity ≤0.025℃, pinpoint gas leaks location quickly
      • Dual-application: Gas leakage detection and thermograph application
      • Temperature range: -20℃~+350℃
      • Inspection without interrupting the process
      • Interchangeable lenses available
      • Built-in 5.0 MP digital camera
      • Folding and 270°rotatable display

Specifications

 

Parameters  TI 330+
Detector Data
Type Cooled FPA, Type II Super Lattice(T2SL)
IR resolution 320 x 256
Pixel Pitch  30μm 
Spectral range

3.1~3.5μm

NETD/Sensitivity 25mK
VOC gas sensitivity ≤0.001ml/s
Lens
FOV/Focal distance   10°×7.5°/55mm
Minimum imaging distance 2m
IFOV 0.55mrad
Focus Manual
Image Performance
Display 5”,color LCD, 800×480 pixels
Built-in visible light camera 5 megapixel CMOS, autofocus, 1 LED fill light
Frequency 50Hz
Digital zoom 1X~8X continuous
Colour palettes 12 palettes(including iron, rainbow, white-hot and black hot etc.)
Contrast/brightness Auto/Manual
Measurement
Temperature range -20℃~+350℃
Temperature accuracy  ±2℃/±2%(reading)
Spotmeter 10 adjustable spots
Line profile Vertical/Horizontal
Area 5 adjustable boxes with max./min./avg temperature value
Image Storage
Storage  8G SD card(can be extended to 32G)
Video output Card reader, USB, WiFi 
IR image format JPEG, 14-bit measurement data image included
Video storage High definition video stored in SD card(MPEG4/H.264 format), recording time up to 1 hour for per video
Voice annotation 40s voice record, stored with per image
Periodic image storage 10s to 24h
Power System
Battery type Rechargeable li-ion battery
Charging system In-camera, AC adapter, car charger
Laser Point Grade/Type Class 2,1mW/635nmRed
Operation temperature range -15℃ to +40℃
Storage temperature range -20℃ to +50℃
Humidity  ≤95%(Non-condense)
Size & Weight 308mm×142mm×166mm, ≤2.5kg(with standard lens)
Main Gas Detection VOC, benzene
Wednesday, 13 January 2021 09:24 Written by

TD 100

TD100 is an innovative NDT - Non-Destructive Testing equipment, which detects, pinpoints and documents flash-arc corona and arcing partial discharge camera. Being with high sensitivity, it is a power tool to detect UV emission in full daylight with high signals from faraway and nearby sources.

TD100 is an ideal predictive maintenance device for overhead transmission lines and high voltage substations. It is widely used in Transmission line inspection, electrical utilities, HV research institutes, HV Electrical component inspection, HV panel inspection, service providers, laboratories and so on

Features

      • High sensitivity up to 3.0 × 10-18watt / cm2
      • Noise interference is small, using an all-day blind detector
      • Accurate superposition and positioning of the whole area of ultraviolet and visible light
      • Hand-held inspection, easy to complete the inspection
      • Synchronous focusing of ultraviolet and visible light
      • SD card online upgrade function
      • High integration and low power consumption
      • Professional report analysis software, more conducive to on-site situation analysis
      • Small size, light weight, easy to operate

Specifications

 

Parameters  TD 100
Minimum UV sensitivity 3.0×10-18watt/cm2
Minimum discharge detection 5pC@10m
Radio voltage detector sensitivity 3.6dBμV@1MHz
Spectral range  240-280nm 
Field of View (FOV)

6.4° x 4.8°

Focus Auto/Manual(Follow visible light)
Zoom 2x
Detector life span No Degradation
LCD screen   Visible 5” LCD screen under sunlight, 800×480
Image modes Display only ultraviolet light image/display only visible light image/combination of visible light and ultraviolet light
UV/Visible overlay accuracy  ≤1mrad
Status Indicators Battery power, gain, photons, date, focusing mode, stacking module, GPS
User configuration settings Corona colour (White, Red, Green, Yellow, Purple), Time, Sleep Mode, Alarm threshold
Image format JPG
Video format AVI
Media download Via Card Reader, USB
Storage capacity 1000+ images or >1 hr video/1GB
External power DC: 9V~12V
Battery type Lithium battery (rechargeable)
Operation runtime 4h continuous (normal temperature)
Power Consumption 10W
Operation   with single phase 230 V ±10% or battery 
Mains adaptor AC:110V~240V or DC: 50Hz~60Hz/9V 3.8A
Operating temperature -10°C  to +50°C
Storage temperature  -25°C to +60°C
Humidity  90% non-condensing
Encapsulation  IP 54 
Size & Weight  290mm×136mm×87mm , 1.39 kg 
Wednesday, 06 January 2021 11:04 Written by

CFL PP3+

The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.

For pinpointing it is used along-with CFL SG Series Surge Generators and for route tracing it is used along-with CFL AG Series Audio Frequency Generators. Advanced technology with features like time-lapse measurement, makes it a tool that can tackle complicated faults easily.

Features

  • Compact, Lightweight and Rugged
  • Operation via User Friendly 5.7” colour Touchscreen Display
  • Universal Receiver used for Route Tracing and Pinpointing
  • Backlit facility with intensity control for ease of viewing in direct sunlight
  • Simultaneous display of Magnetic and Acoustic waveforms
  • Time-lapse / delay measurement facility
  • Automatic Fault Point Indication using Coincidence Method
  • Noise suppression filters to eliminate external influences
  • Mute function for headphones to disable noise while moving
  • Route guidance (Compass) feature during Pinpointing
  • Detection of live loaded cable (50Hz frequency)
  • Specially designed lightweight, neck carrying case ensuring minimum strain to the operator
  • Inbuilt Rechargeable Battery
  • Water-resistant and dustproof design
  • Supplied in an IP67 Class Molded Case

Specifications

Parameters  CFL PP3+
Channels Acoustic and Magnetic (Dual Channel)
Operating Principle Coincidence Method
Gain Up to 120dB adjustable for Acoustic & Magnetic
Volume limitation warning 84dB
Headphone Jack  3.5mm
O/P impedance of headphone 8Ω to 72Ω (32Ω is recommended)
Acoustic Channel Bandwidth 70Hz to 3000Hz with automatic filtering
Magnetic Channel Bandwidth 120Hz to 20kHz Auto-tuned
Battery 11.1V Lithium-Ion Rechargeable
Charger Input 90V to 270V AC, 50/60 Hz, Single Phase
Operating Time 10 Hours Min (Approx)
Display  5.7'', 320 x 240 pixel, Colour, TFT Touch Screen
Environmental -20°C to 55°C, 95% RH (Non-Condensing)
Dimensions of Receiver 231mm x 90mm x 135mm
Weight of Receiver 1.4 kg

Tuesday, 05 January 2021 11:22 Written by

Cable Identification System

After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.

Cable Identification is the most critical and safety-related sequence during all the procedure of Cable Fault Location. The correct identification of a cable out of a bundle of cables, where most of them can be in service, has to be carried out not only carefully, but also by means of an instrument widely eliminating the possibility of human error or misinterpretation.

The Cable Identification System, CFL CIS from SCOPE is the ultimate solution for identifying wanted (dead) cable from a bunch of cables in a trench, pit or cable rack. The SCOPE’s Cable Identification System, CFL CIS is designed to fulfil these most important safety aspects

Features

  • Compact, Lightweight and Rugged
  • User Friendly LED Indication for Right & Wrong Cable Identification from multiple cables
  • Thin and Flexible Current Clamp for easy insertion between closely mounted Cables
  • 10 Stage amplifier setting for better signal identification
  • Transmitter operation through Mains as well as In-built rechargeable battery
  • Transmitter housed in IP67 class moulded case
  • Neck Belt arrangement for easy carrying of Receiver

Specifications

Parameters  CIS 
Pulse Amplitude Selectable between 100A (55V) / 60A (36V)
Pulse Sequence 10 or 20 or 30 pulses/min, User configurable
Pulse Modulation  Alternative pulse at 1s and 2.5s
Pulse Width 72ms
Display 4 line x 20 characters backlit LCD
Power 90V to 265V AC, 50/60Hz or In-built 11.1V Lithium Ion Rechargeable battery
Battery Operating time 6 Hours Min.
Environmental  -20°C to +55°C, 95% RH (Non-Condensing)
Dimensions & Weight 339mm x 295mm x 152mm, 6 Kg approx

 

Parameters  CIS-R
Display Type LED Scale
Flexible Clamp 150mm Diameter
Sensitivity 100% at 31Ω loop resistance
Amplifier 10 stage gain setting
Power 11.1V Lithium-Ion Rechargeable Battery 
Operating Time 8 Hours Min
Environmental  -20°C to +55°C, 95% RH (Non-Condensing)
Dimensions & Weight 210mm x 124mm x 51mm, 0.7 Kg approx

 

Tuesday, 05 January 2021 09:18 Written by

Surge Generator

Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator for fault distance measurement and also used with a PinPointer for pinpointing the fault spot.

SCOPE offers CFL SG Series Surge Generators up to 32kV and 2000 Joules. They are compact, rugged, user friendly and have all safety features in place. They are the ideal choice for fault location on all type of power cables. It can also be mounted in a cable test van for quick fault location if one wants to opt for optional van mounted configuration.

For prelocation it is used in ICM (Impulse Current Method) and SIM (Secondary Impulse Method) / MIM /ARC modes. In this modes, one also needs to use SIM Filter for stabilising the arc at fault. For pinpointing it is used as Thumper to create magnetic as well as acoustic signal across the fault, which is sensed by Pin Pointer. 

 

Features

  • Compact, Lightweight and housed in a rugged aluminium case
  • Available with 16kV and 32kV Models with energy options such as 500J, 1000J, 1500J & 2000J
  • Ideal choice for fault location on all type of power cables
  • Backbone of Cable Fault Locator System
  • Generates short duration high voltage surge for fault break down
  • Used to determine the fault distance in conjunction with Prelocator unit
  • Repetitive surges applied for pinpointing the exact fault location in conjunction Pinpointing set
  • Supports SIM/ARM/MIM method for locating High resistance and flashing faults along with Prelocator and SIM Filter
  • Available with optional modes such as DC Hipot, Burn Down and Sheath Fault Locator Mode

Specifications

Parameters  CFL SG1610 / SG 1620 CFL SG3210/SG3215/SG3220
Output Voltage Range   0- 4, 0-8, 0-16kV 0-8, 0-16, 0-32kV
Output Energy 1000J /2000J 1000J / 1500J /2000J
Impulse Period Sequence Single Impulse / 3S / 6S / 9S or other as desired
Measurement Mode Supported ICM (Impulse Current Method), SIM (Secondary Impulse Method) / MIM / ARC
Ouput Indiaction  Moving Coil Meters
Power  230V AC ±10%, 50Hz
Housing Elegant, rugged aluminium housing with trolley mounting
Dimension 484 x 360 x 580 mm 700 X 700 X 880 mm
Weight  65 kg / 70 kg 95 kg / 105 kg / 115 kg

Optional 'DC HiPOT' Mode

Voltage  0-16kV 0-32kV
Current  up to 12mA up to 24mA

Optional 'Burn Down' Mode 

Voltage  0- 4, 0-8, 0-16kV 0-8, 0-16, 0-32kV
Current  0-90, 0-60, 0-30mA in resp ranges 0-240, 0-120, 0-60mA in resp ranges

Optional 'Sheath Fault Locator' Mode

Voltage 0-8kV
Current  0-60mA 0-240mA
Test Timing Interval Single Impulse / 3S / 6S / 9S or other as desired